Skip to content
Which Vacuum Bag

Hoover H64 dust bags

If your machine is one of the models below, the bag you need is the Hoover H64 (Purepower, TRTE range).

Hoover Purepower and TRTE cylinder vacuum ranges.

Specification

ReferenceHoover H64 (Purepower, TRTE range)
FitsHoover Purepower and TRTE cylinder vacuum ranges
Capacity3 litres (typical for the H64 shape)
MaterialMulti-layer synthetic fleece with card collar
Bags per box4 bags plus filters (standard retail pack)

What to check before you order

H64 is one of two common current Hoover shapes; do not confuse it with the H30 reference used on Freespace and Telios Extra models, which uses a differently shaped collar.

How to replace it

  1. Unplug the vacuum and open the dust compartment door.
  2. Lift out the full dust bag by its card or plastic collar, keeping it level so it does not spill.
  3. Check the collar shape against the Hoover H64 (Purepower, TRTE range) before fitting the new one; a bag that does not sit flush will not seal.
  4. Slide the new dust bag collar into the machine's bag holder until it clicks or seats fully home.
  5. Close the compartment door. Most machines will not run, or will run with reduced suction, if the door is not fully latched.
  6. Run the vacuum briefly on an empty patch of floor to confirm suction feels normal before doing a full clean.

Common mistakes

  • Buying by vacuum model number alone instead of checking the bag shape, which leads to a bag that does not seal.
  • Reusing a bag past the fill line printed on it, which chokes airflow and can strain the motor.
  • Forcing a bag from a different reference into the holder; if it does not seat without pressure, it is the wrong one.

How this reference sits in the Hoover range

Hoover also uses the Hoover H30 shape, and the two are not interchangeable. Compare before you order:

Other Hoover referenceFitsCapacity
Hoover H30 (Freespace, Telios Extra range)Hoover Freespace and Telios Extra cylinder vacuum ranges3.5 litres (typical for the H30 shape)

How long a pack lasts

A retail pack holds 4 dust bags. At the usual rhythm of one change every four to eight weeks in an average household, that pack covers roughly 4 to 8 months, so most people buy bags once or twice a year rather than monthly.

The 3 litre capacity is the volume the bag holds, not a fitting measurement: two bags of the same capacity can have completely different collars. Use it to judge how often you will be changing the bag, and the collar shape to judge whether it fits. Our guide on how often to change a vacuum bag explains what shortens that interval.

Where this information comes from

The specification above is taken from dustbag.co.uk Hoover fitment listings, cross-checked against Hoover UK product documentation. References are re-checked when a manufacturer renumbers a pack; if you find a discrepancy with your own machine, tell us and the page is corrected.

Tools, workspace and measurements before fitting

You do not need special tools to change a Hoover H64 bag, but a small amount of preparation prevents dust leaks inside the cleaner. Work on a hard floor or on newspaper, with the vacuum unplugged for at least 30 seconds before opening the bag compartment. Have one new bag ready, a small torch, a dry cloth and, if you are checking an old bag, a ruler or tape measure.

Measure the old collar only as a check, not as the main way to identify the bag. Paper and card collars can swell or bend after use, so allow a tolerance of about 2 mm when comparing edges, slots and hole positions. The important signs are the overall collar outline, the position of the inlet hole and whether the collar slides into the holder without bowing. If the old collar is torn, compare the clean marks left in the bag holder instead.

Check pointPractical figureWhat it tells you
Time to inspect the holder1 to 2 minutesEnough time to find trapped dust, a folded seal or a broken guide.
Safe fill levelAbout two thirds to three quarters full in normal usePast this point, fine dust often reduces airflow before the bag looks completely packed.
Collar seating gap0 mm visible gap at the holder faceA visible gap means unfiltered dust can bypass the bag.
Test run after fitting10 to 20 secondsLong enough to hear leaks or a blocked airflow note without filling the new bag.
Dust settling time before opening2 to 5 minutes after useThis reduces loose dust lifting out when the door is opened.

If you are comparing Hoover references, use the collar and machine range first. The Hoover H30 bag is a common source of confusion because it is also a Hoover cylinder vacuum bag, but its collar shape is not a fallback fit for H64 machines.

Detailed fitting and sealing procedure

Start with the hose removed if your vacuum design allows it, because this gives better access to the bag mouth and reduces the chance of pushing dirt back into the hose. Open the compartment slowly and look at the old bag before moving it. If dust is visible around the bag holder rather than inside the bag, assume the previous bag was not sealed correctly or the collar was damaged.

Hold the full bag by the collar and pull it straight out along the guide path. Do not twist the bag body, because a packed fleece bag can split at the neck if it is dragged sideways. Wipe the holder face, the door seal and the first 3 cm to 5 cm of the inlet stub with a dry cloth. Avoid water inside the compartment. Damp dust can form a hard ring at the inlet and stop the next collar sitting flat.

Before inserting the new bag, open it gently by separating the two faces with your fingers. Do not inflate it with your mouth, because moisture can wet the inner layers. Slide the collar into the holder using even pressure on both sides. The bag body should hang freely into the compartment, with no fold trapped between the collar and the holder. Close the door using normal hand pressure only. If you need to press the door hard with your palm or knee, stop and reopen it, because something is misaligned.

  • Run the vacuum for 10 to 20 seconds with the floor head lifted slightly from the floor, then switch off and reopen the compartment.
  • Check that the collar has not moved and that the bag has started to expand evenly.
  • Look for a grey dust line around the holder, which means air is escaping past the collar.
  • Refit the bag if it has folded, twisted or pulled away from the inlet.

Frequent faults and how to recover

If suction is weak immediately after fitting a new bag, do not assume the bag is full or faulty. A blocked hose, a clogged pre motor filter or a poorly seated collar can give the same symptom within seconds. Disconnect the hose and drop a small dry object, such as a coin sized cap, through it only if the hose is straight and the object can fall out freely. Do not use sharp wire inside the hose, because it can pierce the lining.

If the door will not close, remove the bag and inspect the holder rails. A small piece of the old card collar can remain stuck in the track. This can add only 1 mm or 2 mm of obstruction, but that is enough to hold the door open or crush the new collar. Clear it with fingers or a blunt plastic tool, then try again.

If dust has escaped into the compartment, remove the bag, wipe loose dust, and check the filter before further use. A filter with a visible dust mat can restrict airflow in less than one room of cleaning after a leak. If the vacuum has been run for several minutes with a leaking bag, let the motor cool for 20 to 30 minutes before testing again. For wider Hoover bag identification, see the Hoover vacuum bag guide.

Special cases: fine dust, pets, storage and uncertain models

Fine plaster dust, ash, flour, carpet powder and large amounts of drilling dust shorten bag life sharply. A bag can lose useful airflow after one short job even when it is far below its volume capacity. For building dust, use a suitable workshop extractor instead of a domestic cylinder vacuum unless the vacuum manual clearly permits that use.

Pet hair often fills the bag unevenly because hair mats around the inlet. If suction drops after cleaning one or two rooms, remove the hose and check the inlet path before replacing another bag. A hair mat can sit at the bend before the bag and make a new bag look unused while airflow is poor.

Store spare bags flat, dry and away from direct sunlight. A cupboard temperature between about 5°C and 30°C is suitable for normal household storage. Do not keep loose bags under heavy items, because a bent collar may still slide into the holder but fail to seal under suction.

If the rating plate is worn or the vacuum has been bought second hand, identify the bag from the bag holder and the old bag shape rather than from the cleaner name alone. If you are still unsure, compare the collar carefully before ordering and use the general checks in the vacuum bag FAQ.

Read next