Skip to content
Which Vacuum Bag

What to do if your model is not listed

We only publish a bag reference once we can trace it to the manufacturer's own documentation or a recognised distributor's product listing. That means our catalogue is intentionally smaller than the full range of vacuums sold in the UK, and it is entirely possible your exact model is not covered yet, even though it is a normal, current machine.

What to check first

  • Look at your brand's page on this site, since the same reference often covers a wide range of models within one product family, even if your specific model number is not named.
  • Check the sticker inside your machine's dust compartment door, which usually names the bag type directly.
  • Check your machine's user manual under consumables or spare parts, which will list the manufacturer's own reference.
  • Search your exact model number together with the word bag on the manufacturer's own website, which is the single most reliable source.

Why we do not guess

ApproachResult
Publish a reference only when it traces to an official or verifiable sourceFewer models listed, but every listed reference can be trusted
Publish a plausible looking reference based on similar modelsMore models listed, but some references would be wrong, risking a bag that does not seal or fit

We have chosen the first approach deliberately. A vacuum bag that does not seal properly is not a minor inconvenience, it can let dust bypass the filtration system and reduce suction across the whole machine, so an unverified guess is worse than no answer at all.

If you still cannot find it

Contact the manufacturer directly with your model number, printed on the rating label on the base or rear of the machine. Most manufacturers, including all ten brands covered on this site, publish an official parts finder or customer service line that can confirm the exact reference for any current model.

Record the identification data before you search

Work from the machine, not from the sales name on the box. Set the vacuum on a stable surface, unplug it, and allow 2 minutes for any warm motor housing to cool before opening the bag compartment. Use a phone camera, a torch, and a ruler marked in millimetres. Take one clear photo of the rating label and one clear photo of the inside of the bag door. If the label is curved or glossy, take the photo from two angles so the last digit is readable.

Write down the brand, the full model code, the voltage label if present, and any bag code printed inside the compartment. A useful model code is often 6 to 14 characters long and may include letters, numbers, spaces, or a slash. Do not shorten it. For example, a missing suffix can separate two machines that look almost identical but use different consumables.

  • Use the rating label on the base, rear, or underside as the primary source.
  • Use the dust compartment label as the primary source for the bag type if it is present.
  • Use the old bag collar only as supporting evidence, because it may be an aftermarket bag or the wrong bag already fitted.
  • Keep the original bag until the replacement has been confirmed in the machine.

If you contact a manufacturer or retailer, send the photos rather than typing the data from memory. This avoids common errors such as reading 0 as O, 1 as I, or 5 as S. A full check normally takes 10 to 15 minutes if the machine is clean and the labels are intact.

Measure the old bag without turning the measurements into a guess

Measurements can help a support desk identify a bag, but they should not be used alone to choose a reference. Many bags share similar paper or synthetic bag sizes while using different cardboard or plastic collars. The collar is usually the critical part because it must locate on the inlet spigot and seal against the compartment face.

Lay the old bag flat on a table without stretching it. Measure the widest part of the bag body, the longest part of the bag body, the collar width, the collar height, and the opening diameter or opening width. Round to the nearest millimetre. If the bag has folded sides, measure it flat, not inflated. Do not cut the bag open, because dust can escape and the original shape may be lost.

Item to recordHow to measure itUseful tolerance for notes
Bag body widthMeasure the flat bag across its widest point.Within about 5 mm is normally enough for identification.
Bag body lengthMeasure from the collar end to the far sealed edge.Within about 10 mm is normally enough for identification.
Collar widthMeasure the complete cardboard or plastic plate.Record to the nearest 1 mm.
Collar openingMeasure the hole, or the inner width if it is not round.Record to the nearest 1 mm.
Seal positionNote whether the seal sits on the front face, rear face, or around the hole.Describe it in words and photograph it.

Also note the material. Paper, microfibre, and synthetic fleece bags can differ in stiffness, but material alone does not prove compatibility. If the machine uses a sliding or hinged bag holder, photograph the holder with the bag removed and again with the bag seated.

Frequent mistakes and safe recovery steps

The most common mistake is searching only the short model family name printed on the front of the cleaner. That name may cover several versions. Recover by finding the rating label and searching the complete code again. If a sticker is damaged, use angled light from a phone torch. Raised or indented print can sometimes be read better from the side than from above.

Another mistake is trusting a bag that was already inside a second hand machine. If the collar looks crushed, taped, trimmed, or forced over the inlet, treat it as unreliable evidence. Remove it carefully, clean the compartment with a slightly damp cloth, and check whether the door closes freely with no bag fitted. Allow the compartment to dry for at least 30 minutes before fitting any paper bag.

If you bought a bag and it does not fit, do not modify the collar. Cutting a larger hole or trimming a locating tab can create an air leak at the exact point where the machine needs a seal. Put the unused bags back in the pack, keep one clean sample aside for comparison, and record why it failed: collar too wide, hole too small, door will not close, holder will not lock, or bag blocks the lid sensor.

If the wrong bag has been run in the cleaner, stop using the machine. Remove the bag outdoors or over a bin, then inspect the pre motor filter. If it is visibly grey with dust, clean or replace it according to the machine manual before further use. Running for even a few minutes with dust bypass can load a small pre motor filter quickly.

Special cases that need extra care

Some machines were sold under more than one retailer name, or had several close variants with different suffixes. In these cases, the complete model code matters more than the brand name on the front panel. If the model was imported, the UK support page may not list it, so use the rating label data and ask the manufacturer for the consumable reference used in the country of sale.

Workshop, ash, wet and dry, and commercial tub vacuums need particular caution. They may use bags, cartridge filters, foam sleeves, or combinations of these parts depending on the job. Do not assume that a dust bag is suitable for ash, rubble, wet pickup, or fine plaster dust unless the machine documentation says so. The wrong consumable can block quickly or let fine particles pass into the filter stack.

For very old machines, allow more time. Labels can fade after 10 to 20 years, and old bag references may have been replaced by newer references. Search using the full model code and the old bag code together, then confirm the result with a verifiable source. If you are unsure how we handle uncertain references, see the FAQ.

Read next