Hoover vacuum bags
Hoover has run several parallel bag ranges across its cylinder and upright lines. The two most common in current UK households are the H64 shape used on Purepower and TRTE machines, and the H30 shape used on Freespace and Telios Extra machines.
How to identify your Hoover model
Hoover identifies its bags by an H number, printed in large type on the bag packaging and on the bag collar itself. The machine model is on a label on the underside of the body and usually starts with a two or three letter range code, such as TRTE for the Purepower cylinders or TFS for the Freespace range.
If you have the old bag, the H number on its collar settles the question in seconds. If the machine came to you second hand and empty, match the range code from the underside label against the table below rather than guessing from the shape of the lid.
Bags for Hoover machines
Each reference below has its own page on this site with the full list of machines it fits, the fitting steps and the mistakes that cost people a pack of bags.
| Bag reference | Fits | Capacity | Bags per box |
|---|---|---|---|
| Hoover H64 (Purepower, TRTE range) | Hoover Purepower and TRTE cylinder vacuum ranges | 3 litres (typical for the H64 shape) | 4 bags plus filters (standard retail pack) |
| Hoover H30 (Freespace, Telios Extra range) | Hoover Freespace and Telios Extra cylinder vacuum ranges | 3.5 litres (typical for the H30 shape) | 4 bags plus filters (standard retail pack) |
Where Hoover owners go wrong
- Reading H30 as interchangeable with H64. They belong to different cylinder generations and the collars are not the same.
- Trusting a listing that says 'fits all Hoover'. Hoover has run several parallel bag lines for decades and no single bag covers the range.
- Ordering from the retail name on the lid alone. Purepower and Freespace are range names that each spanned several years and more than one bag shape.
When to change the bag
Hoover cylinders lose suction noticeably before the bag is physically full, because the paper clogs from the inside as fine dust builds a layer against it. If the machine starts leaving grit on a carpet it cleared easily last week, change the bag before assuming the brush bar or hose is at fault.
Hoover bags: common questions
My bag collar has no number printed on it. What now?
Check the inside of the bag door: Hoover prints the compatible H numbers on a sticker there on most models. Failing that, the range code on the underside label will point you to the right family.
Do Hoover bags come with filters?
Retail packs usually include at least one motor filter. Fit it when you start a new pack rather than saving it, because a clogged motor filter undoes most of the benefit of a fresh bag.
Is it worth buying the larger multipacks?
Only if the bag reference is settled. A five pack of the wrong shape is a more expensive mistake than a single bag of the right one.
Equipment and measurements to take before fitting
Use the old bag as the main measuring tool. Do not use the cardboard shape alone, because a collar can look close while the inlet hole sits a few millimetres out of line. A mismatch of 3 mm to 5 mm at the seal is enough to leak fine dust into the bag chamber.
- Use a ruler with millimetres, not a tape measure with rounded marks.
- Use a clean cloth to wipe the inlet stub and the rubber seal before checking the fit.
- Use a torch to inspect the bag chamber, because spilled dust often hides behind the front lip.
- Keep the old collar until the new bag has been fitted and the lid has closed without force.
Measure the distance from the centre of the inlet hole to the nearest straight edge of the collar. Then measure the height and width of the collar. These figures do not identify the bag on their own, but they show whether a new bag is sitting in the same position as the old one. If the hole is offset, the machine may run, but dust can bypass the bag during the first few minutes of use.
Step by step fitting procedure
Unplug the cleaner first. Open the bag door slowly, because a full bag can lean against the door and spill dust when released suddenly. Slide the old bag out in the direction of the collar guides. Do not pull the paper body of the bag, because it can tear around the collar when the bag is heavy.
Wipe the guide rails, the inlet stub and the area below the bag seat. If there is loose dust in the chamber, remove it before fitting the new bag. Dust left under the collar can lift one edge and create a leak. Check the motor filter before the new bag goes in. If it is grey, matted, or visibly loaded with powder, change it before closing the machine.
Push the new collar fully into the guides until it reaches its stop. The bag body should unfold into the chamber without being trapped under the collar. Close the lid using normal hand pressure only. If the lid needs extra force, open it again and check that the bag corners are not caught between the casing and the door. For the specific fitting notes, use the separate pages for Hoover H30 bags and Hoover H64 bags.
| Check | Practical figure | What it tells you |
|---|---|---|
| Collar movement after fitting | Less than 2 mm by hand | The collar is seated in the guides rather than resting on top of them. |
| Lid closing force | Normal finger pressure | Extra force usually means the bag is folded into the seal area. |
| First test run | 30 to 60 seconds | This is long enough to reveal leaks, whistling, or a bag that inflates in the wrong position. |
| Filter inspection interval | Every new pack of bags | This prevents a blocked filter from being confused with a blocked hose. |
Frequent mistakes and how to recover
If dust has escaped into the bag chamber, do not fit another bag straight away. Remove loose dust from the chamber, wipe the seal, and inspect the motor filter. If the filter has taken visible dust, replace it before running the machine again. Running for even 2 or 3 minutes with dust past the bag can load the filter and reduce airflow.
If the lid will not latch, do not trim the collar and do not bend the latch. Remove the bag and look for a trapped lower corner. Many paper bags expand wider when opened, and the bottom edge can sit under the door hinge line. Fold the bag body lightly into the chamber, then refit the collar squarely.
If suction is poor after a new bag is fitted, test the machine for 30 seconds with the hose removed from the body. If airflow improves at the body inlet, the restriction is in the hose, wand, or floor tool. If airflow is still weak, check the motor filter and the exhaust path before assuming the bag is at fault.
If a new bag falls out when the door is opened, compare the old and new collars side by side. Pay attention to the position of the inlet hole and the guide slots, not only to the outside outline. If the collar cannot lock into the guides, stop using it and identify the correct bag again.
Special cases for older or second hand machines
A second hand Hoover may arrive with a non original bag already fitted. Treat that bag as evidence, not proof. Check whether the collar sits flat, whether the inlet hole lines up cleanly, and whether there is dust behind the bag. Dust behind the bag is a sign that the previous owner may have used a near fit.
Machines stored in a garage or shed need an extra check. Paper bags can absorb moisture and soften, even when unused. If a spare bag feels limp, smells damp, or has a wavy collar, do not use it for fine dust. A softened collar can pull away from the inlet as soon as the bag inflates.
After building work, ash, plaster dust, or fireplace dust, change the bag early. Very fine dust blocks the pores long before the bag is full. In this case the useful capacity can be far below the nominal capacity because airflow, not visible fullness, is the limiting factor. For general identification questions, see the vacuum bag FAQ.
Read next
- AEG vacuum bags: Which bag reference fits your AEG vacuum cleaner, model by model, with sourced specifications.
- Bosch vacuum bags: Which bag reference fits your Bosch vacuum cleaner, model by model, with sourced specifications.
- Electrolux vacuum bags: Which bag reference fits your Electrolux vacuum cleaner, model by model, with sourced specifications.
