Skip to content
Which Vacuum Bag

Electrolux vacuum bags

Electrolux popularised the s-bag system in the 1990s and it remains the reference bag for most classic and mid-range cylinder models, though recent ranges have moved to the redesigned GR200S bag with a wider opening.

How to identify your Electrolux model

Electrolux machines that take an s-bag say so: the s-bag logo is printed inside the dust compartment door, and that logo is the licence mark for the whole system. If it is there, an s-bag fits, whatever the machine is called on the lid.

The model code is on a plate on the underside of the body. Note it before ordering, because a minority of Electrolux cylinders sit outside the s-bag system and take a different reference entirely.

Bags for Electrolux machines

Each reference below has its own page on this site with the full list of machines it fits, the fitting steps and the mistakes that cost people a pack of bags.

Bag referenceFitsCapacityBags per box
Electrolux/AEG s-bag Classic (and s-bag Classic Long Performance)Most Electrolux and AEG cylinder vacuums sold from the mid-1990s through the 2010s that carry the s-bag logo on the dust compartment3 litres (Classic); the Long Performance variant adds an extra layer for slightly longer service life at the same capacity4 or 5 bags depending on pack, plus a motor filter in most packs
Electrolux/AEG GR200SNewer Electrolux and AEG cylinder ranges that moved away from the classic s-bag opening to a wider inlet3.5 litres4 bags (standard retail pack)

Where Electrolux owners go wrong

  • Treating the s-bag colours as different shapes. The Classic, Clinic, Anti-odour and Long Performance variants all share one collar and differ in the filtration media and service life.
  • Assuming a newer Electrolux is bagged. Several recent ranges moved to bagless bins and no s-bag applies to them.
  • Discarding the motor filter that comes in the pack. It is included because it should be changed roughly when the pack runs out.

When to change the bag

s-bags hold three litres and the machines have an indicator, but fine dust blinds the paper before the bag fills. Change it when suction softens on carpet rather than waiting for the indicator to be fully red, and fit the pack's motor filter at the same time on the last bag of a pack.

Electrolux bags: common questions

Is an s-bag from another brand safe in an Electrolux?

The s-bag standard is licensed and used beyond Electrolux and AEG, so a genuine s-bag from a licensed maker fits. Check the logo on the pack rather than the brand name.

What is the difference between Classic and Long Performance?

Capacity is the same. Long Performance adds a synthetic fleece layer, which holds airflow for longer before the bag blinds.

The machine has no s-bag logo. What do I do?

Read the model code on the underside plate and match it against the references listed on this site before ordering anything.

Detailed fitting procedure for an Electrolux bag

Work with the cleaner unplugged, with the hose removed and the dust compartment fully open. Allow 2 to 3 minutes for settled dust to drop inside the old bag before you pull it out, especially after drilling dust, ash, plaster dust or flour.

  • Have the new bag ready before removing the old one, so the compartment is open for the shortest possible time.
  • Hold the cardboard or plastic collar, not the paper body of the bag. Pull straight out along the guide rails or carrier slot.
  • If the old bag has a closing flap, press it shut before lifting the bag out of the machine.
  • Wipe loose dust from the bag chamber with a dry cloth. Do not wet the chamber, because damp dust can block the new bag pores quickly.
  • Slide the new collar fully into the holder until it reaches the stop. A bag that is 5 mm short of the stop can leak around the inlet.
  • Spread the bag body inside the compartment before closing the lid. Do not leave it folded under the collar.
  • Close the lid without force. If the lid needs pressure, reopen it and check that the collar is seated flat.

The whole change should take less than 5 minutes. If dust escapes when the machine is first switched on, stop at once. The usual cause is a collar sitting above the inlet tube rather than around it.

Equipment, checks and figures to use

You need a dry cloth, a small torch, the replacement bag, and the motor filter if you are changing it at the same time. A ruler is useful when the old bag is missing and you need to compare the inlet shape. Do not cut a bag collar to make it fit, because the seal depends on the collar edge staying flat and stiff.

CheckFigure to go byWhat it means in practice
Bag chamber cleaning time1 to 2 minutesEnough to remove loose dust without disturbing seals or wiring.
Normal bag change time3 to 5 minutesLonger usually means the collar is not entering the holder correctly.
Short seating errorAbout 5 mmSmall enough to miss by eye, large enough to let dust bypass the bag.
Motor filter inspectionEvery pack, or sooner after fine dustA grey, loaded filter reduces airflow even with a new bag fitted.
Dust settling pause2 to 3 minutesUseful after fine material, so less dust spills during removal.

If the machine uses the classic licensed format, use the dedicated Electrolux AEG s-bag page to check the fitting sequence for that collar. If the dust port is visibly wider and the machine is from a newer bagged range, compare it with the Electrolux AEG GR200S page before ordering.

Frequent fitting mistakes and how to recover

If the lid will not close, do not press it down with body weight or clamp it shut. Remove the bag and check for three things: the collar is upside down, the bag body is trapped under the hinge side, or the holder has not returned to its home position. Refit the collar slowly and watch the inlet tube enter the collar opening.

If the cleaner loses suction immediately after a new bag is fitted, open the compartment and look for a collapsed bag. This happens when the paper body was left tightly folded. Remove the bag, shake it open gently while holding the collar, and refit it with the body spread into the available chamber space.

If dust is found behind the bag, remove the bag and clean the chamber before running the motor again. Check the collar edge for a crease, torn paper, or a distorted plastic plate. A damaged collar should not be reused. Fit a fresh bag and inspect the motor filter, because bypass dust can load it in a few minutes.

If the bag indicator shows red with a new bag, disconnect the hose and test again for 10 seconds. If the indicator drops back, the blockage is in the hose, wand or floor tool. If it stays red, inspect the motor filter and the exhaust path. A blocked filter can feel like a full bag.

Special cases before you order

Some Electrolux owners inherit a machine without the last bag inside it. In that case, do not order from the lid name alone. Open the dust compartment, photograph the bag holder and the inlet tube, then read the rating plate on the underside. The holder shape is more reliable than the colour of the old bag packaging.

Fine renovation dust is a special case. Plaster, brick dust and sanding dust can block a bag surface long before the rated volume is reached. Expect a much shorter service interval, sometimes after one room of sanding. Change the bag when airflow falls, and inspect the motor filter at the same time.

Odour is another special case. If a smell remains after fitting a new bag, the source may be old dust in the hose, a dirty floor tool, or a loaded filter rather than the bag itself. Remove hair and compacted dust from the floor tool, then run the machine for 30 seconds with the hose disconnected to separate a hose smell from a body smell.

If you are still unsure, use the site FAQ to check the basic identification steps before opening a pack. Once a bag has been forced into the wrong holder, the collar can be marked or bent, and it may no longer seal correctly even in the right machine.

Read next