Electrolux and AEG s-bag
If your machine is one of the models below, the bag you need is the Electrolux/AEG s-bag Classic (and s-bag Classic Long Performance).
Most Electrolux and AEG cylinder vacuums sold from the mid-1990s through the 2010s that carry the s-bag logo on the dust compartment.
Specification
| Reference | Electrolux/AEG s-bag Classic (and s-bag Classic Long Performance) |
|---|---|
| Fits | Most Electrolux and AEG cylinder vacuums sold from the mid-1990s through the 2010s that carry the s-bag logo on the dust compartment |
| Capacity | 3 litres (Classic); the Long Performance variant adds an extra layer for slightly longer service life at the same capacity |
| Material | Multi-layer paper (Classic) or synthetic fleece (Long Performance) |
| Bags per box | 4 or 5 bags depending on pack, plus a motor filter in most packs |
What to check before you order
s-bag is a licensed system used across several brands beyond Electrolux and AEG, but always confirm the s-bag logo is printed inside your machine's dust compartment door before buying, since not every Electrolux model uses it.
How to replace it
- Unplug the vacuum and open the dust compartment door.
- Lift out the full dust bag by its card or plastic collar, keeping it level so it does not spill.
- Check the collar shape against the Electrolux/AEG s-bag Classic (and s-bag Classic Long Performance) before fitting the new one; a bag that does not sit flush will not seal.
- Slide the new dust bag collar into the machine's bag holder until it clicks or seats fully home.
- Close the compartment door. Most machines will not run, or will run with reduced suction, if the door is not fully latched.
- Run the vacuum briefly on an empty patch of floor to confirm suction feels normal before doing a full clean.
Common mistakes
- Buying by vacuum model number alone instead of checking the bag shape, which leads to a bag that does not seal.
- Reusing a bag past the fill line printed on it, which chokes airflow and can strain the motor.
- Forcing a bag from a different reference into the holder; if it does not seat without pressure, it is the wrong one.
How this reference sits in the Electrolux range
Electrolux also uses the Electrolux/AEG GR200S shape, and the two are not interchangeable. Compare before you order:
| Other Electrolux reference | Fits | Capacity |
|---|---|---|
| Electrolux/AEG GR200S | Newer Electrolux and AEG cylinder ranges that moved away from the classic s-bag opening to a wider inlet | 3.5 litres |
How long a pack lasts
A retail pack holds 4 dust bags. At the usual rhythm of one change every four to eight weeks in an average household, that pack covers roughly 4 to 8 months, so most people buy bags once or twice a year rather than monthly.
The 3 litre capacity is the volume the bag holds, not a fitting measurement: two bags of the same capacity can have completely different collars. Use it to judge how often you will be changing the bag, and the collar shape to judge whether it fits. Our guide on how often to change a vacuum bag explains what shortens that interval.
Where this information comes from
The specification above is taken from Electrolux official s-bag compatibility documentation. References are re-checked when a manufacturer renumbers a pack; if you find a discrepancy with your own machine, tell us and the page is corrected.
Tools, checks and working space before you open the cleaner
Do the job on a hard floor, not on carpet. Fine dust drops out of a used bag collar easily, and it is easier to wipe from vinyl, tile or sealed wood. Allow about 10 minutes for a careful change, including cleaning the bag bay and checking the sealing face.
- Use a bin bag or waste sack with an opening at least 300 mm wide, so the old bag can be lowered straight in without tilting it.
- Keep a dry cloth or kitchen paper ready for dust on the bag holder rails and around the inlet stub.
- Use a small torch if the cleaner has a deep bag compartment. The rear of the holder is where misalignment is easiest to miss.
- Do not use water inside the bag compartment unless the machine manual says the part is washable. A damp compartment can clog a paper or fleece bag very quickly.
- If you have asthma or dust sensitivity, leave the cleaner switched off for 5 to 10 minutes after use before opening it, so loose dust settles inside the bag.
Before removing the used bag, look at how the collar is sitting in the holder. Take a phone photo if needed. This gives you a reference for the angle, the rail position and the depth of insertion when fitting the new bag.
Detailed fitting procedure with checks during the job
Open the cover fully and support it with one hand if the hinge is loose. Pull the used bag only by the rigid collar, not by the paper or fleece body. Keep the collar upright until it is above the waste sack. If the machine has a sliding shutter on the old bag, close it before moving the bag across the room.
With the bag removed, check three contact areas. The first is the inlet stub, where air enters the bag. The second is the flat sealing face around that inlet. The third is the pair of guide rails or the frame that holds the collar. Dust packed into any of these areas can hold the new collar 1 or 2 mm away from the seal, which is enough to let fine dust bypass the bag.
Fit the new bag slowly. The collar should travel in the same direction as the old one came out. Use light pressure with two fingers on the stiff part of the collar. If the collar bends, stop and withdraw it. A correctly aligned bag normally needs firm guidance, not force. Once seated, run a fingertip around the visible collar edge to check that it lies flat and even.
Close the lid without pressing on the bag body. If the lid stops before the latch engages, open it again and check that the bag has not folded over the holder or trapped itself under the lid rim. After closing, run the vacuum for 15 to 20 seconds with no tools blocked. A steady motor note and normal airflow at the hose are better signs than noise alone.
Figures to use when diagnosing poor fit or low suction
| Observation | Likely cause | Practical check |
|---|---|---|
| Lid needs heavy pressure to shut. | The collar is not fully home, or the bag body is trapped under the cover. | Open the lid and reseat the collar before trying again. Do not use the latch to force alignment. |
| Dust appears in the bag compartment after one short clean. | Air is bypassing the bag seal. | Wipe the inlet face, refit the bag and check for a flat contact all around the collar. |
| Suction drops within 5 minutes of fitting a new bag. | A blockage may be in the hose, wand or floor head, not in the bag. | Disconnect the hose and test airflow at the cleaner inlet for 10 seconds. |
| Bag looks partly full but suction is already weak. | Fine plaster dust, ash or flour can block pores before the volume is full. | Replace the bag after this type of dust, even if it is below the printed fill mark. |
| New bag collar creases during fitting. | The wrong holder path is being used, or the bag is being pushed off angle. | Compare the collar shape with the removed bag and check against the alternative Electrolux reference if uncertain. |
If the old bag is missing, use the dust compartment rather than the outside model name as your guide. The printed marking inside the compartment is more reliable than a badge on the cleaner body. For Electrolux ranges that use a different holder, compare with Electrolux and AEG GR200S before ordering.
Special cases and recovery after a mistake
If you have run the cleaner with the bag badly seated, stop at once and unplug it. Remove the bag, then wipe the inside of the compartment with a dry cloth. Check the motor filter area next. If visible dust has reached the filter, replace or clean that filter according to the cleaner manual before using the machine again. Running for even 2 or 3 minutes with dust bypass can load the filter heavily.
After vacuuming building dust, fireplace ash, toner, flour or large amounts of pet hair, use a shorter change interval. These materials can block airflow long before the 3 litre volume is reached. In this case, judge by suction and motor sound rather than by how swollen the bag looks.
If the bag tears during removal, do not shake the cleaner. Keep the compartment open, lift out large pieces by hand, then wipe the holder and inlet. Fit a new bag and run the machine briefly. If dust blows from the exhaust or the motor note rises sharply, stop and check the filters.
For older Electrolux or AEG cleaners where labels are worn, search by the machine family as well as by the compartment marking. The general Electrolux vacuum bag guide can help separate bag systems used across different ranges. If the cleaner has no clear marking and no old bag to compare, use the checks in the vacuum bag FAQ before buying.
Read next
- About Which Vacuum Bag: Why this site exists, how the catalogue is sourced, and how it is funded.
- Karcher WD2 and WD3 fleece filter bags: The exact bag reference for Karcher WD2 and WD3 wet and dry vacuum ranges.
- Karcher WD4, WD5, WD5 P and WD6 PS fleece filter bags: The exact bag reference for Karcher WD4, WD5, WD5 P and WD6 PS wet and dry vacuum ranges.
