Skip to content
Which Vacuum Bag

Numatic NVM-1CH dust bags

If your machine is one of the models below, the bag you need is the Numatic NVM-1CH.

Standard-size Henry (HVR200), Hetty, James and George dry vacuums (the common domestic and light commercial Numatic range).

Specification

ReferenceNumatic NVM-1CH
FitsStandard-size Henry (HVR200), Hetty, James and George dry vacuums (the common domestic and light commercial Numatic range)
Capacity9 litres
MaterialMulti-layer paper with a flo-bag design
Bags per box10 bags (standard retail pack)

What to check before you order

NVM-1CH is the most widely stocked Numatic bag and fits the majority of the standard-size Henry family. Always check the litre capacity printed on your machine's body before ordering, since Numatic also sells a larger machine size.

How to replace it

  1. Unplug the vacuum and open the dust compartment door.
  2. Lift out the full dust bag by its card or plastic collar, keeping it level so it does not spill.
  3. Check the collar shape against the Numatic NVM-1CH before fitting the new one; a bag that does not sit flush will not seal.
  4. Slide the new dust bag collar into the machine's bag holder until it clicks or seats fully home.
  5. Close the compartment door. Most machines will not run, or will run with reduced suction, if the door is not fully latched.
  6. Run the vacuum briefly on an empty patch of floor to confirm suction feels normal before doing a full clean.

Common mistakes

  • Buying by vacuum model number alone instead of checking the bag shape, which leads to a bag that does not seal.
  • Reusing a bag past the fill line printed on it, which chokes airflow and can strain the motor.
  • Forcing a bag from a different reference into the holder; if it does not seat without pressure, it is the wrong one.

How this reference sits in the Numatic range

Numatic also uses the Numatic NVM-2BH shape, and the two are not interchangeable. Compare before you order:

Other Numatic referenceFitsCapacity
Numatic NVM-2BHLarger-capacity Henry Xtra and George wet and dry machines15 litres

How long a pack lasts

A retail pack holds 10 dust bags. At the usual rhythm of one change every four to eight weeks in an average household, that pack covers roughly 10 to 20 months, so most people buy bags once or twice a year rather than monthly.

The 9 litre capacity is the volume the bag holds, not a fitting measurement: two bags of the same capacity can have completely different collars. Use it to judge how often you will be changing the bag, and the collar shape to judge whether it fits. Our guide on how often to change a vacuum bag explains what shortens that interval.

Where this information comes from

The specification above is taken from Numatic official spares documentation and Henry Hoover Shop UK product listings. References are re-checked when a manufacturer renumbers a pack; if you find a discrepancy with your own machine, tell us and the page is corrected.

Tools, checks and working space before fitting

You do not need specialist tools, but a clean fitting area prevents dust from falling into the motor filter or the tub. Allow 5 minutes for a normal change and 10 minutes if the old bag has split or overfilled. Work with the vacuum on a flat floor, with at least 50 cm of space on each side so the head can be lifted away without tipping the tub.

  • Use disposable gloves if the bag contains plaster dust, ash, pet hair or old food debris.
  • Keep a bin liner open next to the vacuum before lifting the old bag out.
  • Use a torch if the bag holder is dusty, because the collar slot can look seated when it is only partly engaged.
  • Use a soft brush or dry cloth to clear loose dust from the bag holder. Do not wet the holder before fitting a paper bag.
  • Check the motor filter while the bag is out. If it is grey, matted or clogged across more than half of its surface, clean or replace it before judging suction.

Do not judge the fit by the length or folded shape of a loose bag. A folded paper bag can look smaller than expected before airflow opens it. The meaningful fitting point is the collar and the way it sits against the inlet. If you are comparing several Numatic machines in the same building, label the cupboard shelf rather than the loose bags, especially if a larger reference is also kept nearby. The larger alternative is covered separately at Numatic NVM-2BH bags.

Detailed fitting and sealing procedure

After removing the old bag, spend about 30 seconds checking the inlet stub and the flat area around it. Any ring of compacted dust can stop the new collar sealing evenly. A gap of only 1 mm is enough to leak fine dust into the tub. Brush the area dry, then fit the new bag without twisting the paper body.

Hold the collar square to the holder and push it in using two thumbs, one on each side of the inlet hole. Do not push on the paper body first, because this can crease the top fold and leave the collar half seated. Once the collar is home, lift the paper body gently and open the main folds so the bag can inflate. Leave the lower part of the bag loose in the tub, not trapped under the rim or pressed behind the filter.

Before closing the machine, look for three points: the inlet passes cleanly through the collar opening, the collar lies flat, and no part of the bag is pinched between the head and the tub. Run the machine for 10 to 15 seconds, then switch it off and reopen it. A correctly fitted bag will have started to expand evenly. If one side stays flat, the bag may be folded under itself or blocked by the tub wall.

Figures to use when diagnosing poor suction

CheckPractical figureWhat it means
Normal fitting timeAbout 5 minutesLonger usually means the holder needs cleaning or the wrong bag is being tried.
Test run after fitting10 to 15 secondsEnough time for the bag to inflate without filling the room with dust if it leaks.
Safe fill level for fine dustAbout two thirds fullFine plaster, ash and sanding dust reduce airflow before the bag looks full.
Visible collar gapAny gap over 1 mmStop and reseat the bag, because dust can bypass the bag.
Filter inspection intervalEvery bag changeA clean bag will not restore airflow if the filter is already blocked.

If suction is still weak after a new bag is fitted, check the hose, wand and floor tool before blaming the bag. A coin, screw cap or compacted hair plug can block a hose while leaving the bag almost empty. Detach the hose and drop a small soft object through it, such as a dry cloth corner. It should pass through without stopping. More general checks are listed in the vacuum bag FAQ.

Frequent faults, recovery and special cases

If dust appears inside the tub after a change, stop using the machine and remove the bag. Wipe the holder, check that the collar is not bent, then refit a fresh bag. Do not keep using a bag that has leaked around the collar, because the card or seal may already be distorted. If the motor filter has taken loose dust, clean it before the next run so the motor is not starved of airflow.

If the bag tears while being removed, keep the head off the tub and place the whole tub inside a bin liner if possible. Tip the loose dust out slowly, then wipe the rim and inlet area dry. Do not vacuum the spilled contents back into the same machine without a correctly fitted fresh bag and a checked filter.

Fine building dust is a special case. Even a small amount can blind the bag surface quickly, often within one room of sanding or drilling cleanup. Change the bag early rather than waiting for the nominal capacity. Damp debris is another special case. A paper dry bag should not be used for liquid pickup or wet sludge. If the machine has been used wet, let the tub, hose and inlet dry fully before fitting a dry dust bag again.

For households with more than one Numatic vacuum, keep old packaging or write the bag reference on the storage box. Machines from the same brand can use different bag shapes, and visual checks are faster when the correct family is already separated. The broader brand page is at Numatic vacuum bags.

Read next