Electrolux and AEG GR200S dust bags
If your machine is one of the models below, the bag you need is the Electrolux/AEG GR200S.
Newer Electrolux and AEG cylinder ranges that moved away from the classic s-bag opening to a wider inlet.
Specification
| Reference | Electrolux/AEG GR200S |
|---|---|
| Fits | Newer Electrolux and AEG cylinder ranges that moved away from the classic s-bag opening to a wider inlet |
| Capacity | 3.5 litres |
| Material | Multi-layer synthetic fleece |
| Bags per box | 4 bags (standard retail pack) |
What to check before you order
GR200S has a wider collar opening than the classic s-bag and the two are not interchangeable. If your current bag does not sit flush, check whether your model uses GR200S instead of s-bag.
How to replace it
- Unplug the vacuum and open the dust compartment door.
- Lift out the full dust bag by its card or plastic collar, keeping it level so it does not spill.
- Check the collar shape against the Electrolux/AEG GR200S before fitting the new one; a bag that does not sit flush will not seal.
- Slide the new dust bag collar into the machine's bag holder until it clicks or seats fully home.
- Close the compartment door. Most machines will not run, or will run with reduced suction, if the door is not fully latched.
- Run the vacuum briefly on an empty patch of floor to confirm suction feels normal before doing a full clean.
Common mistakes
- Buying by vacuum model number alone instead of checking the bag shape, which leads to a bag that does not seal.
- Reusing a bag past the fill line printed on it, which chokes airflow and can strain the motor.
- Forcing a bag from a different reference into the holder; if it does not seat without pressure, it is the wrong one.
How this reference sits in the Electrolux range
Electrolux also uses the Electrolux/AEG s-bag Classic shape, and the two are not interchangeable. Compare before you order:
| Other Electrolux reference | Fits | Capacity |
|---|---|---|
| Electrolux/AEG s-bag Classic (and s-bag Classic Long Performance) | Most Electrolux and AEG cylinder vacuums sold from the mid-1990s through the 2010s that carry the s-bag logo on the dust compartment | 3 litres (Classic); the Long Performance variant adds an extra layer for slightly longer service life at the same capacity |
How long a pack lasts
A retail pack holds 4 dust bags. At the usual rhythm of one change every four to eight weeks in an average household, that pack covers roughly 4 to 8 months, so most people buy bags once or twice a year rather than monthly.
The 3.5 litre capacity is the volume the bag holds, not a fitting measurement: two bags of the same capacity can have completely different collars. Use it to judge how often you will be changing the bag, and the collar shape to judge whether it fits. Our guide on how often to change a vacuum bag explains what shortens that interval.
Where this information comes from
The specification above is taken from Electrolux official parts documentation and UK retailer fitment listings. References are re-checked when a manufacturer renumbers a pack; if you find a discrepancy with your own machine, tell us and the page is corrected.
Detailed fitting check before the first clean
Allow 5 to 10 minutes for the first fitting, even if you have changed vacuum bags before. The important check is not the litre capacity, it is the way the collar sits in the holder and seals around the inlet spigot.
Place the vacuum on a hard floor with good light. Remove the old bag and wipe the bag holder, the door seal, and the plastic inlet with a dry cloth. Dust packed around the inlet can add 1 to 2 mm of thickness, which is enough to stop a new collar from sitting flat.
Hold the new bag by the collar, not by the fleece body. Offer it to the holder without pushing. The collar should enter squarely and stop at the same depth on both sides. If one side sits higher by more than about 2 mm, remove it and check for trapped bag material, a bent holder rail, or a piece of the old bag collar left behind.
After the collar is seated, spread the bag body inside the compartment by hand. Do not leave it folded tightly under the lid. A folded bag can block the inlet during the first 30 seconds of use, giving the same symptom as a wrong bag. Close the door with normal hand pressure only. If the latch needs a hard press, open it again and inspect the seating.
For Electrolux model families and naming patterns, use the Electrolux vacuum bag guide as a second check before ordering more bags.
Equipment, measurements, and practical figures
No specialist tool is needed, but a few simple checks prevent most fitting errors. A ruler is useful when comparing the old and new collar, especially if the old bag is damaged or swollen with dust.
| Check | Figure to use | What it tells you |
|---|---|---|
| Time to inspect and fit one bag | 5 to 10 minutes | Enough time to clean the holder and avoid forcing the collar |
| Acceptable side to side seating difference | About 0 to 2 mm | More than this suggests dirt, a bent rail, or the wrong collar shape |
| Gap between collar and sealing face | Ideally no visible gap | A visible gap can leak fine dust into the compartment |
| Initial test run | 20 to 30 seconds | Confirms that the bag opens and airflow is not blocked |
| Post fitting inspection | After the first room, about 5 minutes of use | Shows whether dust is escaping around the collar |
Use a straight edge if the old collar looks warped. Lay it on a flat table. If one corner lifts several millimetres, do not use that bag as the only shape reference. Compare the machine holder and the new collar instead.
Do not wet the compartment or the bag holder before fitting. Moisture can make fine dust stick to the seal and can also soften cardboard parts on used bags. If you have cleaned the area with a damp cloth, wait at least 30 minutes with the compartment open before fitting a new bag.
Frequent faults and how to recover
If suction is weak immediately after fitting, stop the machine within 30 seconds. Open the compartment and check whether the bag has been pulled against the inlet instead of opening into the compartment. Remove it, shake the bag body gently so it unfolds, and refit the collar squarely.
If fine dust appears inside the bag compartment, do not continue vacuuming. Remove the bag and clean the compartment with a dry cloth. Inspect the sealing face for a grey dust track. A dust track on one side usually means the collar was not fully seated on that side. Refit a fresh bag if the collar is bent or contaminated.
If the door will not close, do not trim the collar and do not compress the bag with tools. Check that the holder rails are empty and that the bag body is inside the compartment, not trapped in the hinge or latch side. A trapped fold as small as 10 to 15 mm can stop the door from latching correctly.
If the vacuum sounds higher pitched than usual, airflow may be restricted. Check the hose, wand, floor tool, and pre motor filter before blaming the bag. A blocked floor tool can fill the bag unevenly and make the machine behave as if the bag is full.
- If the wrong bag was forced into the holder, remove it carefully and inspect the plastic rails for cracks before fitting the correct bag.
- If dust has bypassed the bag, clean the compartment and check the filter before the next full clean.
- If the bag holder has moved out of position, reseat it by hand only if it is designed to clip back, otherwise stop and identify the machine model.
- If the old bag has burst, treat the next 5 minutes of running as a test and inspect the compartment again afterwards.
Special cases and cross checks
Some households keep more than one Electrolux or AEG cylinder vacuum. Do not mix bags between machines by brand name alone. A machine that takes the classic s-bag shape may look similar from outside, but the collar opening and holder are different. If you also have an older cylinder vacuum, compare it with the Electrolux and AEG s-bag page before using the same box of bags in both machines.
After building work, fireplace ash, plaster dust, or large amounts of fine powder, change the bag earlier than usual. Fine dust blocks the pores of synthetic fleece before the bag looks full. In that case, a half full bag can still reduce airflow noticeably.
Pet hair creates the opposite problem. The bag may look bulky before it is heavy because hair takes up space. If the door becomes harder to close near the end of a bag, replace it rather than compressing the contents. Compressing hair and dust can push debris back toward the collar.
If the vacuum has been stored in a shed, garage, or cold cupboard, let it stand indoors for about 1 hour before fitting a bag. Condensation on cold plastic can hold dust on the sealing face and reduce the quality of the seal.
For general symptoms such as loss of suction, dust smells, or filter checks, use the vacuum bag FAQ alongside the fitting checks above.
Read next
- Bosch and Siemens Type G dust bags: The exact bag reference for Bosch GL-30, GL-40 and Ergomaxx cylinder ranges; Siemens VSZ and Q-series cylinder ranges.
- Miele FJM dust bags: The exact bag reference for S200 to S600 series canister vacuums sold roughly between 1995 and 2005.
- Miele GN dust bags: The exact bag reference for Complete C3 range, Compact C1 and C2 range, S2, S5 and S8 canister range.
