Siemens vacuum bags
Siemens vacuum cleaners are built on the same platform as Bosch's cylinder range and take the identical Type G bag. If you own a Siemens VSZ or Q-series machine, everything on this site's Bosch Type G page applies to you as well.
How to identify your Siemens model
Siemens prints the model on a plate on the underside of the machine, usually starting with VS or VSZ followed by digits, and repeats the bag type on a sticker inside the dust compartment lid. That sticker is the fastest identifier on the machine.
Because the Siemens cylinder range is built on the same platform as the Bosch one, the bag standard is shared. A Siemens Q-series or VSZ that calls for Type G takes the same bag as its Bosch equivalent, sold under either brand name.
Bags for Siemens machines
Each reference below has its own page on this site with the full list of machines it fits, the fitting steps and the mistakes that cost people a pack of bags.
| Bag reference | Fits | Capacity | Bags per box |
|---|---|---|---|
| Bosch/Siemens Type G (BBZ52AFG2U / VZ52AFG2U family) | Bosch GL-30, GL-40 and Ergomaxx cylinder ranges; Siemens VSZ and Q-series cylinder ranges built on the same platform | 4 litres | 4 bags plus a micro-hygiene filter (standard retail pack) |
Where Siemens owners go wrong
- Searching only under the Siemens part number and paying more for it. The equivalent Bosch-branded pack is the same bag and often sits next to it at a different price.
- Assuming every Siemens cylinder is bagged. Recent ranges include bagless models with a clear bin and no bag reference at all.
- Ordering against the machine's marketing name instead of the type letter inside the lid.
When to change the bag
The indicator window on the body reads airflow rather than weight, so a bag loaded with fine dust will show full while still feeling light. Trust the indicator over the feel of the bag, and check the hose if it reads full again straight after a change.
Siemens bags: common questions
Is the Siemens bag different from the Bosch one?
Not where both are the same type. The part numbers differ by brand but the collar and the fit are identical.
Where is the type letter printed?
On a sticker inside the dust compartment lid on most models, and on the collar of the bag already fitted.
Can I run the machine for one session without a bag?
No. The bag is the first stage of filtration and running without it loads the motor filter with everything the bag would have held.
Detailed fitting procedure for a Siemens bagged cylinder
Work with the cleaner unplugged and cold. If the machine has just been used, leave it for about 10 minutes so that dust is not pulled out of the neck when the lid is opened. Put the cleaner on a flat floor with at least 50 cm of clear space in front of the dust compartment, because the bag must come out straight rather than being folded against the lid.
Open the dust compartment slowly and let loose dust settle for 30 to 60 seconds. Hold the old bag by the cardboard or plastic collar, not by the paper or fleece body. Slide it out in the same direction as the holder guides. If there is a closing flap on the old bag, close it before lifting the bag clear. Put the used bag directly into a household waste sack rather than carrying it through the room uncovered.
Before fitting the replacement, wipe the bag seat and the inside edge of the lid with a dry cloth. Do not use water inside the compartment. Check that the motor filter behind the bag position is flat and not pulled forward. Push the new collar fully into the holder until it reaches the stop. A visible gap of more than 1 or 2 mm around the bag neck is enough to leak dust, so remove it and refit it rather than forcing the lid shut.
Close the lid with light hand pressure only. If it will not close, the bag is not seated or the collar is turned the wrong way. Do not press on the lid with your knee or body weight, because this can bend the holder and cause repeated leakage later.
Equipment, checks and useful figures
You do not need tools for a normal bag change, but a few simple items make the job cleaner and reduce the chance of fitting a damaged bag. Keep the new bag in its packet until the compartment is open, because a bag stored loose in a cupboard can pick up grit or have a creased collar.
- Use one unused replacement bag of the correct type for the machine, checked against the marking inside the dust compartment.
- Use one dry cloth for the lid seal, bag seat and compartment edges.
- Use a household waste sack large enough to take the used bag without compressing it.
- Use a torch if the compartment is dark, because a trapped filter corner or a cracked holder is easy to miss.
- Use a straightened coat hanger only for hose inspection, and cover the end with tape so it does not puncture the hose lining.
| Check | Figure to use | What it means |
|---|---|---|
| Dust settling time after opening the lid | 30 to 60 seconds | This reduces dust escaping when the collar is moved. |
| Cooling time after heavy use | About 10 minutes | This prevents warm airflow from lifting dust during removal. |
| Acceptable visible gap at the bag neck | No more than 1 to 2 mm | A larger gap can let dust bypass the bag. |
| Hose blockage check length | Inspect the full hose, usually over 1 metre | A blocked hose can make a new bag read full at once. |
| Test run after fitting | 20 to 30 seconds on low or medium power | This confirms that the lid is sealed and airflow is normal. |
Frequent mistakes and how to recover
If dust appears inside the compartment after a bag change, stop using the cleaner immediately. Remove the bag, wipe the compartment dry, check that the motor filter has not been loaded with loose dust, and refit the bag from the start. If the filter is visibly clogged, replace or clean it according to the machine instructions before further use.
If the lid closed once but then springs open, do not tape it shut. The common causes are a collar sitting above the guide rails, a bag body trapped in the hinge side, or a filter not seated flat. Open the lid, pull the bag out 2 cm, then push it back in squarely until it stops.
If suction remains poor with a new bag, remove the floor head, wand and hose one at a time. Test airflow at the machine inlet for 20 seconds. Strong airflow at the inlet but weak airflow at the floor head means the restriction is in the hose, tube or nozzle, not in the bag. Long hair, pine needles and small cardboard pieces often lodge at bends rather than at the bag opening.
If the bag collar tears during fitting, discard that bag. A tear at the neck is not repairable with tape because the air stream pulls dust through the repair edge. For more general fault checks, see the vacuum bag FAQ.
Special cases before ordering or using the cleaner
Fine building dust, ash and plaster dust fill the pores of a bag much faster than normal household dust. A bag can lose airflow after a single room of sanding dust even when it feels nearly empty. Do not shake the bag to reuse it, because the fine dust remains in the filter material and can be released into the motor path.
If the cleaner has picked up damp dirt, replace the bag even if it is not full. Damp dust can harden around the neck and can smell after 24 to 48 hours inside a closed compartment. Leave the compartment open for several hours with the machine unplugged, and do not refit a bag until the interior is dry.
For an inherited or second hand Siemens cylinder, do not assume the bag already inside is correct. Use it only as a visual clue, then verify the marking in the dust compartment before ordering. If the holder is missing, cracked or no longer grips the collar evenly, a new bag will not seal reliably until the holder problem is fixed.
If there is no bag holder, no bag chamber and the dirt container is a removable clear bin, the machine is a bagless type and these bags do not apply. In that case, look for filter maintenance information rather than a bag reference.
Read next
- Numatic (Henry) vacuum bags: Which bag reference fits your Numatic (Henry) vacuum cleaner, model by model, with sourced specifications.
- OEM vs compatible vacuum bags: The practical difference between original manufacturer bags and compatible third-party bags, and when each makes sense.
- Panasonic vacuum bags: Which bag reference fits your Panasonic vacuum cleaner, model by model, with sourced specifications.
