Skip to content
Which Vacuum Bag

Panasonic C-20E dust bags

If your machine is one of the models below, the bag you need is the Panasonic C-20E (AMC94KYZ0 retail pack).

Panasonic MC-CG range of cylinder vacuums.

Specification

ReferencePanasonic C-20E (AMC94KYZ0 retail pack)
FitsPanasonic MC-CG range of cylinder vacuums
Capacity2.5 litres
MaterialMulti-layer paper
Bags per box5 bags plus filters (AMC94KYZ0 retail pack)

What to check before you order

C-20E is the standard reference across almost all current Panasonic bagged cylinder models sold in the UK, which makes Panasonic one of the simpler brands to buy for correctly.

How to replace it

  1. Unplug the vacuum and open the dust compartment door.
  2. Lift out the full dust bag by its card or plastic collar, keeping it level so it does not spill.
  3. Check the collar shape against the Panasonic C-20E (AMC94KYZ0 retail pack) before fitting the new one; a bag that does not sit flush will not seal.
  4. Slide the new dust bag collar into the machine's bag holder until it clicks or seats fully home.
  5. Close the compartment door. Most machines will not run, or will run with reduced suction, if the door is not fully latched.
  6. Run the vacuum briefly on an empty patch of floor to confirm suction feels normal before doing a full clean.

Common mistakes

  • Buying by vacuum model number alone instead of checking the bag shape, which leads to a bag that does not seal.
  • Reusing a bag past the fill line printed on it, which chokes airflow and can strain the motor.
  • Forcing a bag from a different reference into the holder; if it does not seat without pressure, it is the wrong one.

How this reference sits in the Panasonic range

Panasonic C-20E (AMC94KYZ0 retail pack) is the only reference published for Panasonic on this site, because it is the only one confirmed by a manufacturer or distributor source. Other Panasonic machines sold in the UK are bagless, so there is no bag to match. Our Panasonic page lists what is covered.

How long a pack lasts

A retail pack holds 5 dust bags. At the usual rhythm of one change every four to eight weeks in an average household, that pack covers roughly 5 to 10 months, so most people buy bags once or twice a year rather than monthly.

The 2.5 litre capacity is the volume the bag holds, not a fitting measurement: two bags of the same capacity can have completely different collars. Use it to judge how often you will be changing the bag, and the collar shape to judge whether it fits. Our guide on how often to change a vacuum bag explains what shortens that interval.

Where this information comes from

The specification above is taken from Panasonic official parts documentation and UK retailer listings for the AMC94KYZ0 pack. References are re-checked when a manufacturer renumbers a pack; if you find a discrepancy with your own machine, tell us and the page is corrected.

Tools, space and checks before you open the machine

You do not need specialist tools to fit a Panasonic C-20E dust bag, but a clean working setup prevents dust escaping into the motor compartment. Work on a hard floor or place the vacuum on newspaper about 60 cm by 60 cm. Keep the hose raised until the old bag is out, because loose grit can fall back from the hose socket when the door is open.

  • Use a dry cloth to wipe the bag bay, the door seal and the plastic bag rails before fitting the new bag.
  • Use a small torch if the bag holder is dark, because the collar must sit flat against the inlet.
  • Keep a household bin bag open beside the vacuum, so the full bag can go straight in without being carried across the room.
  • Allow 5 to 10 minutes for the job if the machine is dusty, or about 2 minutes for a normal bag change.
  • Do not wash the paper bag, the cardboard collar or the inside of the dust compartment. Moisture and paper dust make a paste that can block airflow.

Before fitting the new bag, look at the old collar for bending, torn edges or a crescent shaped dust mark around the inlet hole. A dust mark outside the hole is a sign that the previous bag was not sitting squarely. Check the holder for packed dust in the corners, as even 1 mm to 2 mm of compacted dirt can stop the collar from seating fully.

If you are checking a Panasonic vacuum you have just bought second hand, do not judge the bag only by the model name on the cleaner. Open the compartment and compare the fitted bag shape with the C-20E reference shown on this page. For the wider Panasonic category, use the Panasonic vacuum bag page.

Detailed fitting procedure with practical tolerances

Open the dust compartment with the vacuum unplugged and cold. If the cleaner has been used for a long session, wait about 10 minutes before opening it. Warm dust and fine ash like particles are more likely to rise into the air when the bag is disturbed.

Hold the full bag by the stiff collar, not by the paper body. Pull it out in the same direction as the guide rails. Avoid twisting it, because a twist can tear a full paper bag at the folded side. Put it into the bin bag immediately, then close the bin bag before cleaning the compartment.

Wipe the inlet stub and the flat sealing face around it. The useful check is simple: the sealing face should feel smooth to a fingertip and should not leave a thick grey line on a dry cloth after one wipe. If loose dust is sitting on the seal, the next bag can leak even when it is the correct reference.

Slide the new collar into the holder using light finger pressure only. A correct bag should move along the rails without bowing the collar. If you need both thumbs or you can see the collar bending by more than a few millimetres, stop and remove it. Forcing the collar can leave a gap at the inlet, which sends dust towards the pre motor area instead of into the bag.

After closing the lid, run the vacuum for 10 to 15 seconds with the floor head lifted slightly from the floor. Listen for a steady motor note. A sudden high pitched sound, a lid that will not latch, or weak suction at the hose end means the bag is not seated or there is another blockage.

Figures to use when deciding whether to change the bag

SituationPractical figureWhat to do
Normal household dustCheck every 4 weeksChange when suction drops or the bag feels firm across most of its body.
Fine plaster dust or soot like dustCheck after 10 to 15 minutes of cleaningStop early, because fine dust can block the paper pores before the bag looks full.
Pet hair and fluffCheck after 2 to 3 full house cleansHair can fill the bag volume quickly but may still feel springy, so judge by airflow as well.
After fitting a new bagTest for 10 to 15 secondsConfirm normal suction before cleaning carpets, stairs or upholstery.
Dust found inside the bag bayClean before the next bag is fittedLook for a collar seating problem, a split bag or dirt trapped on the seal.

Do not wait for the bag to become hard from end to end. A bag can still have unused volume but have poor airflow because the outer paper layers are loaded with fine dust. This is common after DIY dust, fireplace dust, flour, talc or very old carpet powder. In those cases, airflow is a better guide than volume.

If you want a general rule for change intervals and suction loss, see the vacuum bag FAQ.

Frequent faults, recovery and special cases

If the lid will not close, remove the bag and check that the collar is not sitting above the guide rails. Do not press the lid down to force the latch. A forced lid can crease the collar and create a leak. Refit the bag from the start, keeping the collar flat and aligned with the inlet.

If suction is poor immediately after fitting, remove the hose and test suction at the machine inlet for 5 seconds. Strong suction at the inlet but weak suction at the hose end points to a hose, tube or floor head blockage. Weak suction at the inlet points to a bag seating problem, a full bag, a blocked filter area or an air leak at the compartment door.

If dust has escaped into the compartment, take out the bag and wipe all visible dust with a dry cloth. Pay attention to the lower corners and the door seal. Fit a fresh bag only when the sealing face is clean. If dust returns after one short test run, stop using the vacuum until the cause is found, because dust bypassing the bag can reach the motor protection area.

Special care is needed after picking up fine renovation dust. Even a small amount, for example dust from drilling several wall plugs, can reduce airflow faster than ordinary house dust. Change the bag sooner than normal and check the filter area before further use.

Do not use the vacuum for damp debris, wet carpet powder or fresh fireplace ash. Damp material can swell inside a paper bag and block airflow. Ash that appears cold can contain very fine particles that load the bag surface quickly. If either has been picked up by mistake, stop, change the bag, wipe the compartment and test suction before continuing.

Read next