Skip to content
Which Vacuum Bag

Panasonic vacuum bags

Panasonic's MC-CG range of cylinder vacuums uses the C-20E bag, a straightforward single reference that covers the vast majority of the brand's bagged machines sold in the UK over the last decade.

How to identify your Panasonic model

Panasonic bagged cylinders sit almost entirely in the MC-CG range, and the model number is printed on a label on the underside of the machine. The range is unusually consistent, which is why Panasonic is one of the simpler brands to buy bags for once you have confirmed the machine is bagged.

The bag reference is printed on the collar of the fitted bag and on the retail pack. If the machine is empty and second hand, the model number on the underside label is enough to match against the reference listed on this site.

Bags for Panasonic machines

Each reference below has its own page on this site with the full list of machines it fits, the fitting steps and the mistakes that cost people a pack of bags.

Bag referenceFitsCapacityBags per box
Panasonic C-20E (AMC94KYZ0 retail pack)Panasonic MC-CG range of cylinder vacuums2.5 litres5 bags plus filters (AMC94KYZ0 retail pack)

Where Panasonic owners go wrong

  • Ordering by the retail pack code alone without checking it covers your model. The pack code and the bag reference are two different strings.
  • Assuming an upright or a cordless Panasonic takes the same bag as the cylinder range. It does not.
  • Running the machine with the bag door not fully latched. On these models a door that is not closed properly drops suction sharply and is often mistaken for a full bag.

When to change the bag

At two and a half litres the bag is smaller than most rivals, so it fills sooner in ordinary use. Change it at around two thirds full, and change the filters included in the retail pack when you reach the last bag in the box.

Panasonic bags: common questions

Does one reference really cover the whole bagged range?

It covers the vast majority of the current bagged cylinder models sold in the UK. Check your model number against the table above before ordering in quantity.

Do the retail packs include filters?

The standard pack includes filters alongside the bags. Fit them when the pack runs out rather than storing them.

The machine lost suction right after a bag change. Why?

Check the bag door is fully latched and the hose is clear. Both drop suction in a way that feels exactly like a full bag.

Detailed bag change procedure

Work with the vacuum unplugged and cold. Put the cleaner on a stable floor, not on a chair, because the hose and lid can pull the body sideways while you are working. Allow about 60 cm of clear space in front of the machine for the lid, the hose and the old bag.

  • Open the bag chamber slowly so dust on the bag collar is not shaken into the housing.
  • Before pulling the bag out, look at the cardboard collar and note which face points towards the hose inlet. This is the easiest way to avoid fitting the new bag backwards.
  • Hold the collar, not the paper body of the bag, and slide it out in the same direction as the guide rails.
  • Check the chamber with a torch. Remove loose dust with a dry cloth. Do not use water inside the vacuum body.
  • Fit the new bag by pushing the collar fully into the holder until it sits flat. A collar that is 3 mm to 5 mm short of its stop can still let the lid close, but it can leak at the inlet.
  • Close the lid with one hand pressing near the latch. Do not force it. If the lid resists, reopen it and check that the bag collar is not folded or trapped.
  • Run the vacuum for 10 seconds with the floor head lifted. A smooth change in motor sound is normal. A fluttering sound usually means the bag is not sealed at the inlet or the hose is partly blocked.

If you need the model specific fitting notes, use the dedicated Panasonic C-20E bags page before buying more packs.

Equipment, working sizes and useful figures

You do not need special tools, but a torch and a dry cloth make the job cleaner. A small waste bag is useful because the old bag can release dust when it is flexed. If the cleaner has been used on fine renovation dust, wear a basic dust mask and change the bag outdoors if possible.

CheckPractical figureWhat it tells you
Time for a normal bag change3 to 5 minutesLonger usually means the collar is not sliding into its holder cleanly.
Clear working spaceAbout 60 cm by 60 cmEnough room to open the lid, handle the hose and keep the new bag clean.
Safe fill level before changingAbout two thirds of the bag volumeLeaves air space so suction does not collapse before the bag looks completely full.
First test run after fitting10 to 20 secondsEnough time to hear leaks, rattles or a blocked hose without overheating the machine.
Blockage check lengthFull hose length, then wand, then floor headMost sudden suction faults after a bag change are caused by a plug of fluff moving into a narrow part.

Keep one unused bag in the cupboard with the vacuum rather than in a damp shed. Paper bags and cardboard collars can deform if stored where humidity is high, and a warped collar is harder to seal squarely against the inlet.

Frequent mistakes and how to recover

If dust appears inside the bag chamber after a new bag is fitted, stop using the vacuum. Remove the bag and check the collar for a crease, torn slot or dust trapped between the collar and the holder. Clean the seating area with a dry cloth, then refit the bag. Do not tape a damaged collar into place, because tape can lift and leak once warm air passes over it.

If the lid will not close, do not press harder. A forced lid can bend the collar or leave the latch half engaged. Remove the bag, flatten the collar by hand, and slide it back in while watching both side edges. The collar must sit evenly, not at an angle.

If suction is weak immediately after a correct bag change, disconnect the hose and test suction at the machine inlet for a few seconds. Strong suction at the inlet points to a hose, wand or floor head blockage. Weak suction at the inlet points to a badly seated bag, a chamber leak, a full filter or a lid that is not latched.

If the vacuum smells dusty after a change, check for loose dust behind the bag and around the inlet. Fine dust left in the chamber can be blown against the new bag and smell like a leaking bag even when the fit is correct. For general fault checks that apply across bagged vacuums, see the vacuum bag FAQ.

Special cases before ordering or fitting

A second hand Panasonic can arrive with no bag, the wrong bag, or an old bag fitted only for storage. In that case, do not use the installed bag as proof of compatibility. Use the model label on the machine and the bag reference information on this site instead.

After building work, plaster dust, ash and very fine powders can fill the pores of a bag before the bag is physically full. In that situation a bag may need changing after a small amount of visible debris. If suction falls quickly during this type of cleaning, stop, change the bag, and check the filters rather than continuing until the bag looks full.

If the machine has picked up damp dirt, remove the bag as soon as possible. Moist dust can harden inside the bag and can also soften the cardboard collar. Let the bag chamber air dry with the lid open before fitting a fresh bag. Never dry a damp disposable bag for reuse.

If a bag is nearly full and the vacuum will be stored for more than a month, replace it before storage. A partly full bag can hold odour, grit and fine dust against the inlet area, and the next user may mistake the reduced airflow for a machine fault.

Read next

  • Hoover vacuum bags: Which bag reference fits your Hoover vacuum cleaner, model by model, with sourced specifications.
  • Karcher vacuum bags: Which bag reference fits your Karcher vacuum cleaner, model by model, with sourced specifications.
  • Miele vacuum bags: Which bag reference fits your Miele vacuum cleaner, model by model, with sourced specifications.