AEG vacuum bags
AEG shares its parent company Electrolux's bag platform. Most AEG cylinder vacuums take the same s-bag as Electrolux models, with newer AEG ranges moving to the GR200S bag alongside their Electrolux equivalents.
How to identify your AEG model
AEG belongs to the Electrolux group and its cylinder machines share the bag platform. The dust compartment door carries the s-bag logo on the models that use the system, which is the quickest confirmation you can get without a part number.
The model code, usually starting with AVQ, VX or LX depending on the generation, is printed on a plate on the underside of the machine. Note it before buying: the newer AEG ranges have moved steadily towards bagless designs and those take no bag at all.
Bags for AEG machines
Each reference below has its own page on this site with the full list of machines it fits, the fitting steps and the mistakes that cost people a pack of bags.
| Bag reference | Fits | Capacity | Bags per box |
|---|---|---|---|
| Electrolux/AEG s-bag Classic (and s-bag Classic Long Performance) | Most Electrolux and AEG cylinder vacuums sold from the mid-1990s through the 2010s that carry the s-bag logo on the dust compartment | 3 litres (Classic); the Long Performance variant adds an extra layer for slightly longer service life at the same capacity | 4 or 5 bags depending on pack, plus a motor filter in most packs |
| Electrolux/AEG GR200S | Newer Electrolux and AEG cylinder ranges that moved away from the classic s-bag opening to a wider inlet | 3.5 litres | 4 bags (standard retail pack) |
Where AEG owners go wrong
- Searching under the AEG brand only. The identical s-bag is sold under several brand names and the AEG-branded pack is not always the cheapest.
- Assuming a recent AEG is bagged because an older one in the house is. Check the compartment for a bin rather than a bag holder.
- Reading the colour of the bag as a fit difference rather than a filtration grade.
When to change the bag
Fine dust blinds an s-bag well before it is full, and AEG cylinders are quiet enough that the drop in suction is easier to feel than to hear. Change the bag when the machine starts leaving grit behind on a carpet it cleared cleanly a week earlier.
AEG bags: common questions
Can I use an Electrolux s-bag in an AEG?
Yes, where the machine carries the s-bag logo. The two brands share the system.
My AEG has no bag holder at all. Have I missed it?
If the compartment holds a clear plastic bin, the machine is bagless by design and needs filter maintenance rather than bags.
Do AEG packs include filters?
Most retail s-bag packs include a motor filter. Fit it on the last bag of the pack rather than leaving it in the box.
Fitting an AEG vacuum bag without losing the seal
Unplug the cleaner and let it stand for 2 minutes before opening the dust compartment. This avoids pulling fine dust through the inlet while the airflow path is still disturbed. Open the lid fully, not just enough to pull at the bag, because a half open lid often bends the cardboard or plastic collar.
Hold the old bag by its collar and pull it straight out of the holder. Do not lift from the soft body of the bag, as this can tear paper that is already loaded with fine dust. Put the used bag directly into a bin bag and close it before doing any filter work.
Wipe the bag chamber with a dry cloth. If you use a damp cloth, wait at least 30 minutes before fitting a new bag, because damp dust on the collar face can break the seal. Look into the inlet tube from inside the compartment. A pencil, hair clip or compacted plug of grit in the first 5 cm of the tube is enough to make a new bag look faulty.
Slide the new bag collar into the holder until it stops. The collar must sit flat against the holder, with no lifted corner. Close the lid slowly for the last 3 cm. If the lid needs force, stop and reseat the bag. A correct bag lets the lid close with firm resistance, not a snap or a crunch.
Tools, checks and working dimensions
You do not need specialist tools, but a few simple items make the job cleaner and reduce the chance of fitting a good bag badly. Keep the machine on a table or on a sheet of newspaper so that escaped dust is visible.
- Use a torch to check the first bend of the inlet tube and the base of the bag holder.
- Use a dry cloth or kitchen paper for the dust chamber, not a wet wipe that leaves moisture on the seal face.
- Use a ruler only as a check tool. A visible gap of more than about 2 mm between the collar and the holder is enough to cause dust bypass.
- Use scissors only for trimming a plain motor filter sheet, never for altering a bag collar.
- Allow 5 minutes for a normal bag change and 10 to 15 minutes if you also inspect the filters and hose.
| Check point | Useful figure | What it tells you |
|---|---|---|
| Collar seating gap | 0 to 2 mm visible gap | The bag is normally seated well enough to seal. |
| Inlet tube inspection depth | First 5 to 8 cm | Most hard blockages sit close to the bag opening. |
| Motor filter change interval | About every 4 bags if a spare filter is supplied | This keeps fine dust away from the motor side. |
| Fine plaster or ash use | Change after one heavy clean | Fine powder blocks airflow before the bag volume is filled. |
| Lid closing test | Last 3 cm by hand pressure only | Force means the collar or holder is misaligned. |
Frequent fitting faults and how to recover
If dust appears inside the compartment after a new bag has been fitted, do not keep vacuuming to test it. Stop, remove the bag and inspect the collar edge. A creased corner usually means the bag was inserted at a slight angle. Fit a fresh bag if the collar is cracked or permanently bent.
If the lid will not close, compare the position of the collar with the old bag before throwing the old one away. The most common cause is the collar sitting above the guide rail rather than inside it. Push on the collar, not on the soft bag body, and check that the bag is not trapped under the lid hinge.
If suction is poor immediately after fitting, remove the floor head and hose before blaming the bag. Run the cleaner for no more than 10 seconds with the hose removed. If airflow returns at the machine inlet, the blockage is in the hose, wand or floor tool. If airflow is still weak, check the motor filter and outlet filter. More general fault checks are covered in the vacuum bag FAQ.
If the bag pulls out when the lid opens, the holder may be dusty or slightly worn. Clean the grooves with a dry cloth wrapped around a teaspoon handle. Do not add tape, glue or folded card, because these can stop the safety shutter or lid catch from moving correctly.
Special AEG cases to check before buying again
Some AEG owners have more than one machine in the house, often from different generations. Do not assume that a bag kept in a cupboard belongs to the cleaner in front of you. Match the bag to the machine compartment, not to the brand name printed on the packet.
For homes with renovation dust, fireplace ash or large amounts of pet hair, use the bag condition rather than the calendar. A bag used on plaster dust can lose most airflow in one room. A bag used on normal household dust may last several weeks, depending on floor area and how often the cleaner is used.
If the cleaner has been stored in a shed or garage, inspect the unused bags before fitting. A collar that has absorbed moisture may swell by 1 mm or more and drag in the holder. A musty or soft bag should not be used, because it can split when the machine reaches full suction.
If a second hand AEG arrives without a bag holder, do not buy bags first. Open the compartment and check that the holder, inlet seal and motor filter frame are all present. A missing holder can make the correct bag unusable even when the model normally takes one.
Read next
- About Which Vacuum Bag: Why this site exists, how the catalogue is sourced, and how it is funded.
- Panasonic C-20E dust bags: The exact bag reference for Panasonic MC-CG range of cylinder vacuums.
- Vax legacy cylinder dust bags: The exact bag reference for Older Vax 6000 and 6100 series cylinder vacuums.
