Skip to content
Which Vacuum Bag

Karcher WD4, WD5, WD5 P and WD6 PS fleece filter bags

If your machine is one of the models below, the bag you need is the Karcher fleece filter bag, part number 2.863-006.0.

Karcher WD4, WD5, WD5 P and WD6 PS wet and dry vacuum ranges.

Specification

ReferenceKarcher fleece filter bag, part number 2.863-006.0
FitsKarcher WD4, WD5, WD5 P and WD6 PS wet and dry vacuum ranges
CapacityMatched to the WD4 to WD6 tank size (typically 20 to 30 litres tank, bag sized accordingly)
MaterialNon-woven fleece
Bags per box5 bags (standard retail pack)

What to check before you order

This is a larger fleece bag than the WD2/WD3 reference and the two are not interchangeable between machine sizes.

How to replace it

  1. Unplug the vacuum and open the tank lid.
  2. Lift out the full fleece filter bag by its card or plastic collar, keeping it level so it does not spill.
  3. Check the collar shape against the Karcher fleece filter bag, part number 2.863-006.0 before fitting the new one; a bag that does not sit flush will not seal.
  4. Slide the new fleece filter bag collar into the machine's bag holder until it clicks or seats fully home.
  5. Close the compartment door. Most machines will not run, or will run with reduced suction, if the door is not fully latched.
  6. Run the vacuum briefly on an empty patch of floor to confirm suction feels normal before doing a full clean.

Common mistakes

  • Buying by vacuum model number alone instead of checking the bag shape, which leads to a bag that does not seal.
  • Reusing a bag past the fill line printed on it, which chokes airflow and can strain the motor.
  • Forcing a bag from a different reference into the holder; if it does not seat without pressure, it is the wrong one.

How this reference sits in the Karcher range

Karcher also uses the Karcher WD2/WD3 fleece filter bag shape, and the two are not interchangeable. Compare before you order:

Other Karcher referenceFitsCapacity
Karcher WD2/WD3 fleece filter bagKarcher WD2 and WD3 wet and dry vacuum rangesMatched to the WD2/WD3 tank size (typically 12 to 17 litres tank, bag sized accordingly)

How long a pack lasts

A retail pack holds 5 fleece filter bags. At the usual rhythm of one change every four to eight weeks in an average household, that pack covers roughly 5 to 10 months, so most people buy bags once or twice a year rather than monthly.

The 30 litre capacity is the volume the bag holds, not a fitting measurement: two bags of the same capacity can have completely different collars. Use it to judge how often you will be changing the bag, and the collar shape to judge whether it fits. Our guide on how often to change a vacuum bag explains what shortens that interval.

Where this information comes from

The specification above is taken from Karcher official accessories documentation, part number 2.863-006.0 (karcher.com). References are re-checked when a manufacturer renumbers a pack; if you find a discrepancy with your own machine, tell us and the page is corrected.

Tools, workspace and measurements to take before fitting

Set up the vacuum on a flat floor with good light, because the bag collar must sit squarely on the inlet inside the tank. Allow about 60 cm of clear floor space in front of the machine so the lid can be lifted without pulling on the hose or cable.

  • Wear disposable gloves if the old bag contains plaster dust, ash, soil or pet hair, because fine dust will escape if the collar is tilted.
  • Keep a bin bag open beside the vacuum before removing the full bag, so the transfer takes less than 10 seconds.
  • Use a dry cloth to wipe the inlet stub and the bag holder before fitting the new bag.
  • Use a ruler only to compare the old collar with the new collar, not to decide compatibility from tank size.
  • Check the hose for a blockage at the same time, because a blocked hose can feel like a full bag.

If you still have the used bag, measure the visible collar opening, the distance from the collar edge to any locating slots, and the overall collar width. These figures are only a comparison against the new bag in your hand. They are not a substitute for the correct Karcher reference, because collars with close dimensions can still lock differently.

Do not test fit with wet hands or inside a damp tank. A fleece bag fitted into a wet tank can pick up moisture at the base before you start vacuuming, which reduces airflow and can make fine dust cake on the bag surface.

Detailed fitting procedure with checks during the job

Start with the plug removed from the socket and the hose detached if it is pulling the lid sideways. Open the tank slowly and look at the direction of the old bag before moving it. The printed side, folded corners and collar angle are useful references when the new bag is unfolded.

Lift the old bag by the collar with one hand under the body of the bag if it is heavy. A bag containing dry rubble, sawdust or grit can weigh several kilograms even when it is not visibly full. Keep the collar higher than the bag body so dust does not run back through the opening.

Before installing the new bag, tap the folded fleece open with your fingers. Do not pull hard on the seams. The aim is to give the bag enough shape so it can drop into the tank without being trapped under the lid. Slide the collar into the holder in one steady movement until it sits flat against the inlet face.

After the lid is closed, run the vacuum for 5 to 10 seconds with the floor tool lifted from the floor. Listen for a steady motor note. Then place your hand near the hose end for 2 seconds to feel suction. If the sound rises sharply or the hose pulls weakly, stop and reopen the tank before continuing.

Check pointNormal resultAction if wrong
Collar seatingFlat against the inlet, no raised cornerRemove the bag and refit without forcing the holder
Bag positionBag body drops into the tank with no fold under the lidOpen the fleece by hand and rotate it away from the lid seal
First test runStable sound after 5 to 10 secondsCheck the hose, inlet and collar seal
Dust in tank after testNo loose dust outside the bagStop using the bag and inspect the collar fit

Frequent mistakes and how to recover

If the bag has been fitted behind the inlet rather than over it, the vacuum may still run but dust will collect in the tank. Stop immediately, remove the bag, wipe the inlet area and fit a new bag if dust has entered the collar folds. A contaminated collar may not seal reliably after refitting.

If the lid will not close without pressure, do not press down on it. The bag may be sitting across the tank rim or the collar may not be fully home. Open the tank and move the bag body lower into the tank. Closing the lid on trapped fleece can create a leak path of a few millimetres, enough for fine dust to bypass the bag.

If suction falls after only a few minutes on fine dust, the bag surface may be blinded rather than full. This is common with sanding dust, cement dust and fireplace residue. Replace the bag even if it feels light. For these jobs, expect a much shorter change interval than the usual household interval.

If you bought the smaller bag shape by mistake, do not cut, tape or stretch the collar. The smaller WD2 and WD3 bag type is covered separately at Karcher WD2 and WD3 bags. For the wider Karcher range, use the brand page at Karcher vacuum bags.

Special cases: wet pickup, building dust and storage

Remove the fleece bag before wet pickup unless your machine instructions say otherwise for the exact task. A dry dust bag is not a water container. If water reaches the bag, remove it, clean the tank and let the inside dry fully before fitting another bag. Drying the tank for several hours is better than fitting a fresh bag onto a damp base.

For DIY dust, change the bag earlier than you would after normal floor cleaning. A bag that is only one third full can still block airflow if the dust is very fine. Work in short sessions of 10 to 15 minutes, then check motor sound and suction before continuing.

Store spare bags flat, dry and away from sharp tools. Do not leave loose bags in the vacuum tank with screws, drill bits or rubble, because small punctures can turn into tears when suction starts. If you are unsure whether a symptom is caused by the bag, filter or hose, see the general checks in the FAQ.

Read next

  • Hoover H64 dust bags: The exact bag reference for Hoover Purepower and TRTE cylinder vacuum ranges.
  • Miele vacuum bags: Which bag reference fits your Miele vacuum cleaner, model by model, with sourced specifications.
  • Miele FJM dust bags: The exact bag reference for S200 to S600 series canister vacuums sold roughly between 1995 and 2005.